ホーム製品燃料装置の部品

黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品

すべての製品

燃料装置の部品 (60)

IMPCO中型エンジンのミキサー (18)

IMPCO大きいエンジンのミキサー (14)

IMPCOの調整装置 (6)

低圧の調整装置 (7)

高圧調整装置 (3)

IMPCOの修理用キット (6)

IMPCOのガスのミキサー (13)

IMPCO Lockoff (12)

IMPCO LPGの部品 (47)

中国 guangqing(anhui)gas technologies co.,ltd. 認証

オンラインです

黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品

Name: 黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品
Brand: IMPCO
SKU: RK-COBRA
Price: 1.00 USD
Availability: InStock
Rating: 4.6 (117 reviews)

Black Coded Diapragm Impco Cobra Repair Fuel System Parts

大画像 : 黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品

商品の詳細:

起源の場所:	米国
ブランド名:	IMPCO
モデル番号:	RK-COBRA

お支払配送条件:

最小注文数量:	24
価格:	Depending on quantity
パッケージの詳細:	カートン
受渡し時間:	8週
支払条件:	T/T
供給の能力:	8weeksごとの1200pcs

連絡先

詳細製品概要

製品名:

修理用キット

部品番号:

RK-J

ブランド:

IMPCO

ダイヤフラム:

Hydrin （黒）

ハイライト:

RKのコブラのImpcoのコブラの修理用キット

コードされたDiapragm Impcoのコブラの修理用キット

コブラ修理燃料装置の部品

IMPCO RK-J , Model J Regulator Repair Kit , Black Coded Diapragm

The IMPCO PPI-3 repair kit instructions will provide the technician information to successfully repair the Model J regulator converter. Always inspect the major casting pieces for damage, corrosion or cracks before attempting a service repair. Be sure the repair kit part number you are using is correct for the regulator being serviced. Diaphragm is BLACK - Hydrin diaphragm material is the standard material and is well suited for the most common applications

REBUILD INSTRUCTIONS

1. Under normal conditions, installation of a complete Model J Repair Kit should be necessary only at the time of a major engine overhaul or when the converter has been out of service for an extended period of time. Each kit includes the necessary gaskets, diaphragms, seals and some replacement screws.

2. Remove the 6 screws (2) from the secondary cover assembly (3).

NOTE: Identify type and location of screws removed (i.e. Torx) to ensure the same type and size screws are returned to the correct locations during reassembly.

3. Loosen the secondary cover (3) by tapping around the circumference with a plastic screw driver handle.

4. Remove the secondary cover (3) and secondary dia-phragm (4) as a unit. Note the secondary lever (6) pro-truding through the metal tab slot of the secondary dia-phragm. Slide the cover and diaphragm toward the gas inlet to free the lever from the slotted tab of the dia-phragm. Take care not to bend the lever.

5. Remove the screw (5) retaining the secondary lever fulcrum pin.

6. Remove the secondary lever (6) and fulcrum pin (7). Set aside fulcrum pin for reassembly. Remove the secondary spring (9).

7. Turn the converter over. Remove the seven screws (20) and lift off the primary cover (19).

8. Remove the primary diaphragm (18).

9. Remove the primary valve pin (17) and spring (16).

10. Remove plate (14) and the gasket (13).

11. Remove the gasket (13) from the plate (14). Clean plate as needed to ensure a good seal with a new gas-ket.

12. Remove the primary seat (12). Clean covers (3, 14, & 19), body (10) and all other metal parts as necessary with a safety solvent as needed and allow to dry prior to reassembly. Do not use harsh solvents such as brake or carburetor cleaner on any of the non-metallic components as they will damage the material.

13. Install new primary seat (12).

14. Set new plate gasket (13) on the plate (14). The pri-mary pressure hole in the gasket must line up with the hole in the body cover plate as noted in the photo at left.

15. Place the plate (14) and gasket (13) on to the body (10) and align the screw holes.

16. Insert the new primary valve pin (17) through the spring (16) and insert into the plate (14) with the larger diame-ter end of the spring resting against the plate.

17. Set the primary diaphragm (18) in place on the plate (14). Line up the screw holes to the plate.

18. Carefully place the primary cover (19) over the dia-phragm (18). Hand-thread the screws (20) through the cover and plate (14) into the converter body (10).

19. Tighten the screws (20) to 37-43 in-lb. (4.2-4.9 N•m) in a criss-cross pattern.

20. Assemble the new secondary seat (8) and new sec-ondary lever (6) by inserting the seat retaining tip to the end opening of the lever as shown. Be sure the new seat properly locks into place.

21. Position the secondary spring (9) in place on the body (10). Place the secondary lever assembly (6 & 8) into place over the spring (9).

22. Hold the lever assembly (6 & 8) with the fulcrum pin (7) in place in its locating groove and fasten in place with the retaining screw (5).

23. Tighten the screw (5) to 29-35 in.lbs. (3.3-4.0 N•m).

24. The end of the secondary lever (6) should be 1/32" be-low the level of the body casting (10). Use a straight edge to measure. Remove and gently bend the lever if necessary to obtain the correct height.

NOTE: Bending the lever while installed may result in damage to the seat (8). Remove the lever from the body, bend, reinstall, and then re-check the height.

25. Align the secondary diaphragm (4) to the secondary lever (6) as shown. The end of the lever must protrude through the tab slot on the bottom of the new dia-phragm (4) after installation. The gap from which the link is punched should be located toward the gas inlet.

26. Install the secondary cover (3) with the six screws (2).

27. Tighten the screws (2) in a crisscross pattern to 29-35 in-lb. (3.3-4.0 N•m), to complete the installation of the repair kit components.

28. Attach a 100 psi air pressure hose to the regulator "IN-LET" fitting.

29. For models with a primer button: Depress the primer button several times. Air flow should be detected when the primer is depressed.

NOTE: Not all models include a primer button. Skip this step for models without a primer button.

30. Check the primary cover for leaks using liquid leak de-tector solution.

31. Make sure one of the regulator's secondary outlets is plugged. Draw a bubble of leak solution over the other regulator outlet. The bubble should hold for several se-conds when the regulator is pressurized. If any leaks are found, the regulator must be replaced. If no leaks are found, the regulator can be reinstalled and returned to service.

タグ:

コンタクトパーソン: Mrs. Carrie Liu

電話番号: +86 13855195806

ファックス: 86-551-63664756

その他の製品

ULモデルCA125 6 IMPCOガスのミキサーの燃料装置の部品

部分の記述: ミキサー

部品番号: CA125-6

ブランド: IMPCO

ガスタイプ: LPGの蒸気天燃ガス

IMPCOのダイジェスト/低熱ガスDG200M 2 2つのガスの混合装置

製品名: ミキサー

燃料のタイプ: ダイジェストの低熱ガス

土台位置: 縦

ダイヤフラム材料: Hydrin （標準）、シリコーン（任意）

シリコーンのダイヤフラムモデルJ IMPCO修理用キット

製品名: 修理用キット

部品番号: RK-J-2

ブランド: IMPCO

ダイヤフラム: シリコーン（黄色）

標準的な空気弁RK CA55 2 IMPCOの燃料装置の部品

製品名: 修理用キット

部品番号: RK-CA55-2

ブランド: IMPCO

エア燃料の比率: 傾き

FluoroのシリコーンのダイヤフラムRK VFF30 3 IMPCOの修理用キット

製品名: 修理用キット

部品番号: RK-VFF30-3

ブランド: IMPCO

ダイヤフラム: Fluoroのシリコーン

黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品

黒いコードされたDiapragm Impcoのコブラ修理燃料装置の部品

RKのコブラのImpcoのコブラの修理用キット

コードされたDiapragm Impcoのコブラの修理用キット

コブラ修理燃料装置の部品

Impcoの燃料装置PF 052FM,

450098の001の燃料装置の部品,

ろ過15ミクロンPF 052FM